The Class D amplifier topology makes this 2 x 50W amplifier board efficient and consume less space than traditional solid state amplifiers.
Two TDA7498 Class-D amplifier ICs are used on this amplifier board to produce up to 100W into four channels.
Amplifiers this powerful used to take up as much room and generate as much heat as a space heater! Up to 600W of pure Class-D power is on tap and ready for you to use this amplifier board with the meanest subwoofer you can find.
This 2 x 8W Class D dual channel amplifier board employs a Tripath-style Texas Instruments TPA3110 chip. Each channel is rated at 8 watts, delivered with state-of-the-art sound quality.
Step up the output of your smartphone to drive high impedance headphones with this Class AB headphone amplifier board. The LM4881 IC is used to provide up to 15.7 dB of high quality gain to power even the most power hungry headphones.
This 2 x 150W Class-D audio amplifier board integrates TI’s high performance TAS5613 supporting stereo channel audio amplification.
The Sure Electronics AA-JA31211 1 x 60 Watt Class D Audio Amplifier Board with Audio DSP - JAB3-60 an amplifier board easily built in to any project, speaker build or other DIY project in need of a small amplifier board.
The Sure Electronics 2 x 15 Watt 8 Ohm Class D Audio Amplifier with Bluetooth 2.1 – JAB1 is an amplifier board easily built in to any project, speaker build or other DIY project in need of a small amplifier board with enough power to drive stereo speakers
This Sure Electronics audio amplifier board integrates IR's High Voltage, high performance class D audio amplifier driver IRS2092SPBF and 200V Single N-Channel HEXFET Power MOSFET IRFB4227 to deliver 750 watt of power. This amplifier board supports mono a
2,000 watts of clean monoblock power are available with this amplifier board. It integrates high performance IRS2092 and 200V Single N-Channel HEXFET Power MOSFET IRFB4227 supporting single channel audio amplification by using one channel half bridge topo
This 1 x 300W Class-D audio amplifier board integrates TI’s high performance TAS5613 supporting single channel audio amplification.
2,500 watts of clean monoblock power are available with this amplifier board. An IRS2092 controls six IRFB4227 HEXFET power MOSFETS to deliver power effortlessly. Two 60 to 95 VDC power supplies are required for operation. See note below.
This amplifier board uses three Class-D TDA7498s to generate up to 100W x 6-channels, making it the perfect 5.1 amplifier solution.
At 6 watts per dollar, this stereo Class-D amplifier board is a tremendous value pumping out up to 300W per channel. Perfect for use with subwoofers or as a high-end, two-channel critical listening amplifier. 25 to 50 VDC power supply required.
Amplifiers this powerful used to take up as much room and generate as much heat as a space heater! Up to 600W of pure Class-D power is on tap and ready for you to use this amplifier board with the meanest subwoofer you can find.
This 2 x 8W Class D dual channel amplifier board employs a Tripath-style Texas Instruments TPA3110 chip. Each channel is rated at 8 watts, delivered with state-of-the-art sound quality.
The TPA3116 Class D amplifiers provide high-performance, thermally efficient amplifier solutions. This board delivers 100 watts of power in a small package.
Step up the output of your smartphone to drive high impedance headphones with this Class AB headphone amplifier board. The LM4881 IC is used to provide up to 15.7 dB of high quality gain to power even the most power hungry headphones.
This Class-D audio amplifier board gives you 2 x 100 watts using T-AMP technology. Using PBTL (Parallel Bridge-Tied Load) topology you get 50 watts RMS per channel with only 0.01% THD at 4 ohms.
Design your own powered subwoofer, powered speaker or audio amplifier with Sure's 2 x 500 watt stereo amp board. It's ready to handle mid power demanding audio projects.
As the new comer of BCPB (Battery Charging and Protection Board) series, BCPB3 inherits the high efficiency and high reliability of BCPB2, offering more battery holders for commonly used 18650 Lithium batteries. BCPB3 is designed for 5pieces 18650 Lithium
This hybrid Battery Charging and Protection Board is designed for five 26650 Lithium-Ion cells. It supports solar charging, hybrid charging sources and it even has a lot more to offer.
The 3S 18650 Lithium battery charger and balance protection board is a charging and protection module for 3 pcs Lithium batteries pack. It is highly integrated and can be used as portable power bank.
With MPPT charging ICs equipped, this board works as ch
This interface extension board provides a simple connection solution for customer’s applications. With its headers and a 10 pin cable, the interface extension board can easily be integrated to the DSP Kernal board.
