Nog geen account? Account aanmaken
Uw winkelwagen is leeg
High quality RCA jack connectors with nut for most chassis-mount applications.
Gold plated RCA jacks with solder-on design. Works with materials up to 3/16" thick.
Audiophile connectors feature the same high performance features found in exotic connectors at a price that you can afford. Four connectors included.
A great low cost alternative if you are looking for a high-end 3.5 mm panel mount jack chassis for your DIY project enclosures.
A great low cost alternative if you are looking for a 3.5 mm panel mount jack chassis for your DIY project enclosures.
These connectors are designed with the audiophile in mind. 24 kt gold plating ensures the highest possible signal transfer and resists harsh environmental corrosion. These precision-machined connectors are made to last and last.
This 2 pole 6 position shorting rotary switch can be used with projects or replace damaged and worn out rotary switches. Shorting contacts rated to 250 VAC at 150 mA. Steel ball bearing control.
Heavy duty push button momentary switch. 2A @ 250 VAC
Heavy duty push button momentary switch. 2A @ 250 VAC
Automotive top-mount press-fit round rocker switch. 20A @ 12 VDC, 7A @ 250 VAC
Miniature rocker switch. 6A @ 250 VAC
Illuminated SPST rocker. Red switch with neon bulb inside. 8 amp, 250 VAC.
Large, ON-ON, DPDT switch in panel mount. 10A 250VAC
Miniature toggle switch with tapered knob. 3A 250 VAC.
Metal covered toggle with metal pivot pin enables this switch to outlast illuminated plastic toggle switches. Red transparent cover prevents switch from being turned on accidently. Push up to 20 amps @ 12 VDC through it for automotive projects and more.
SPST toggle switch with screw terminals. 10A/250 VAC. 12.7 mm (1/2") mounting hole.
L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This stereo L-pad is rated at 100 watts RMS, is designed to be used with two 8 ohm loads, features
L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This stereo L-pad is rated at 50 watts RMS, is designed to be used with two 8 ohm loads, features a
L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This stereo L-pad is rated at 15 watts RMS and is designed to be used with two 8 ohm loads. Feature
L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This L-pad is rated at 100 watts RMS, is designed to be used with 8 ohm loads, features a 1" shaft
L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This L-pad is rated at 50 watts RMS, is designed to be used with 8 ohm loads, features a 1" shaft l
L pads are recommended for use in tweeter and midrange crossover networks to match individual output levels, while maintaining a constant 8 ohm impedance. 1" shaft allows mounting in 3/4" wood. Includes face plate, knob, hardware, and wiring instructions.
The Alps stereo potentiometers are of the highest quality available. The 6 mm straight shaft is 25 mm long with M8 thru-hole mounting, hardware included. For over 6 decades, Alps has been made in Japan, and has also been the only choice for serious musici
The Alps stereo potentiometers are of the highest quality available. The 6 mm straight shaft is 25 mm long with M8 thru-hole mounting, hardware included. For over 6 decades, Alps has been made in Japan, and has also been the only choice for serious musici
