Noch keinen Account? Benutzerkonto anlegen
Ihr Warenkorb ist leer
The UcD400HG HxR amplifier module is an entry level high-end class D amplifier, with HxR upgrade from Hypex. This amplifier is known for its high performance, reliability and ease of use. The UcD400HG HxR comes with the required UcD Signal Cable.
The Sure Electronics AA-JA32171 2 x 50 Watt 4 Ohm Class D Audio Amplifier with Bluetooth 4.0 APT-X - JAB2-50 is an amplifier board easily built in to any project, speaker build or other DIY project in need of a small amplifier board with enough power to d
This is the upgraded version of the original 2 X 300 watt TAS5630 class D audio amplifier board.This amplifier board supports stereo amplification by using two channel PBTL topology. By means of dedicated heat sink design with temperature controlled fan,
1,500 watts of clean monoblock power are available with this amplifier board. It integrates high performance IRS2092 and IR MOSFET IRFB4227 supporting single channel audio amplification.
Design your own powered subwoofer, powered speaker or audio amplifier with Sure's 2 x 400 watt stereo amp board. It's ready to handle mid power demanding audio projects.
2,500 watts of clean monoblock power are available with this amplifier board. An IRS2092 controls six IRFB4227 HEXFET power MOSFETS to deliver power effortlessly. Two 60 to 95 VDC power supplies are required for operation. See note below.
Choose this 2 x 25 watt amplifier board to power your next speaker project. A Texas Instrument's Class D TDA7492 amplifier chip is employed to produce high fidelity sound efficiently.
Two TDA7498 Class-D amplifier ICs are used on this amplifier board to produce up to 100W into four channels.
Amplifiers this powerful used to take up as much room and generate as much heat as a space heater! Up to 600W of pure Class-D power is on tap and ready for you to use this amplifier board with the meanest subwoofer you can find.
This 2 x 8W Class D dual channel amplifier board employs a Tripath-style Texas Instruments TPA3110 chip. Each channel is rated at 8 watts, delivered with state-of-the-art sound quality.
The TPA3116 Class D amplifiers provide high-performance, thermally efficient amplifier solutions. This board delivers 100 watts of power in a small package.
The Dayton Audio KAB-215 Bluetooth Amplifier Board allows for quick and easy addition of audio to any project. With an output of 2x15 watts, there is more than enough power to drive stereo speakers, yet it is small enough to fit in tight spaces.
The Dayton Audio KAB-250v3 Bluetooth Amplifier Board allows for quick and easy addition of audio to any project. With an output of 2x50 watts, there is more than enough power to drive stereo speakers, yet it is small enough to fit in tight spaces
50cm balanced signal cable with 4-pin connectors on both sides to connect the DLCP to the NC400 module.
The HNR12 is a -12V voltage regulator. Together with the HPR12 it forms the optional HxR upgrade for UcD180HG and Ucd400HG.
SMPS3kA700 2 x 85 VDC 3000 Watt Switch Mode Power Supply is specially designed to be used in combination with an UcD2k module or multiple UcD700HG HxR modules. This SMPS comes with the required Hypex Cable Set SMPS3k.
SMPS3kA400 2 x 65 VDC 3000 Watt Switch Mode Power Supply is specially designed to be used in combination with multiple UcD400HG, UcD400HG HxR or NC400 modules. This SMPS comes with the required Hypex Cable Set SMPS3k.
SMPS1200A700 2 x 85 VDC 1200 Watt Switch Mode Power Supply is specially designed to be used in combination with the UcD700HG HxR module. This SMPS comes with the required Hypex Cable Set SMPS1200.
The Softstart module is used to minimize transformer inrush currents and provide for push button control at the same time.
The FA503 2x500 +100 Watt FusionAmp is a DSP controlled three channel plate amplifier. It can be the basis of a powerful active two- or three-way speaker.
The FA502 2x500 Watt FusionAmp is a DSP controlled two channel plate amplifier. It can be the basis of a two-way active speaker or an active subwoofer.
The FA253 2x250 +100 Watt FusionAmp is a DSP controlled three channel plate amplifier. It can be the basis of a powerful active two- or three-way speaker.
The FA251 250 Watt FusionAmp is a DSP controlled plate amplifier. It can be the basis of a powerful active subwoofer or an active one-way monitor.
The FA123 2x125 +100 Watt FusionAmp is a DSP controlled three channel plate amplifier. It can be the basis of a powerful active two- or three-way speaker.
