Two TDA7498 Class-D amplifier ICs are used on this amplifier board to produce up to 100W into four channels.
At 6 watts per dollar, this stereo Class-D amplifier board is a tremendous value pumping out up to 300W per channel. Perfect for use with subwoofers or as a high-end, two-channel critical listening amplifier. 25 to 50 VDC power supply required.
Amplifiers this powerful used to take up as much room and generate as much heat as a space heater! Up to 600W of pure Class-D power is on tap and ready for you to use this amplifier board with the meanest subwoofer you can find.
This 2 x 8W Class D dual channel amplifier board employs a Tripath-style Texas Instruments TPA3110 chip. Each channel is rated at 8 watts, delivered with state-of-the-art sound quality.
This Class-D audio amplifier board gives you 2 x 100 watts using T-AMP technology. Using PBTL (Parallel Bridge-Tied Load) topology you get 50 watts RMS per channel with only 0.01% THD at 4 ohms.
Design your own powered subwoofer, powered speaker or audio amplifier with Sure's 2 x 500 watt stereo amp board. It's ready to handle mid power demanding audio projects.
The Dayton Audio KAB-215 Bluetooth Amplifier Board allows for quick and easy addition of audio to any project. With an output of 2x15 watts, there is more than enough power to drive stereo speakers, yet it is small enough to fit in tight spaces.
The Dayton Audio KAB-250v3 Bluetooth Amplifier Board allows for quick and easy addition of audio to any project. With an output of 2x50 watts, there is more than enough power to drive stereo speakers, yet it is small enough to fit in tight spaces
Dayton Audio's DTA-2 amp module utilizes a Class-T Tripath audio chip to produce incredible fidelity and efficiency. Add a 12 VDC 2A power supply to this complete PCB, and install smooth, clean audiophile sound almost anywhere.
The Fusion Remote Kit is suitable for extending all FusionAmp models with remote compatibility.
The Hypex Remote Control is a remote controller which can be used in combination with the Fusion Amp remote kit.
The HPR12 is a 12V voltage regulator. Together with the HNR12 it forms the optional HxR upgrade for UcD180HG and Ucd400HG.
The HNR12 is a -12V voltage regulator. Together with the HPR12 it forms the optional HxR upgrade for UcD180HG and Ucd400HG.
SMPS DLCP 2 x 16 VDC 10 Watt Switch Mode Power Supply is specially designed to be used in combination with the DLCP module.
SMPS3kA700 2 x 85 VDC 3000 Watt Switch Mode Power Supply is specially designed to be used in combination with an UcD2k module or multiple UcD700HG HxR modules. This SMPS comes with the required Hypex Cable Set SMPS3k.
SMPS1200A400 2 x 64 VDC 1200 Watt Switch Mode Power Supply is specially designed to be used in combination with multiple UcD400HG, UcD400HG HxR or NC400 modules. This SMPS comes with the required Hypex Cable Set SMPS1200.
The Softstart module is used to minimize transformer inrush currents and provide for push button control at the same time.
DLCP 2x6 Digital Loudspeaker Cross-over Platform is a complete hardware/firmware platform for digitally filtered (6 channels) and corrected active multiway loudspeakers.
The FA503 2x500 +100 Watt FusionAmp is a DSP controlled three channel plate amplifier. It can be the basis of a powerful active two- or three-way speaker.
The FA502 2x500 Watt FusionAmp is a DSP controlled two channel plate amplifier. It can be the basis of a two-way active speaker or an active subwoofer.
The FA501 500 Watt FusionAmp is a DSP controlled plate amplifier. It can be the basis of a powerful active subwoofer or an active one-way monitor.
The FA251 250 Watt FusionAmp is a DSP controlled plate amplifier. It can be the basis of a powerful active subwoofer or an active one-way monitor.
The FA123 2x125 +100 Watt FusionAmp is a DSP controlled three channel plate amplifier. It can be the basis of a powerful active two- or three-way speaker.
The FA122 2x125 Watt FusionAmp is a DSP controlled two channel plate amplifier. It can be the basis of a two-way active speaker or an active subwoofer.
